KM-N2

Caratteristiche

Dispositivo compatto e multicircuito per il monitoraggio dell'energia

  • Oltre 20 anni di storia nella tecnologia di misura dell'energia
  • Compatto con funzionalità multicircuito (fino a 4 circuiti collegati a un dispositivo)
  • Soluzione dei problemi di progettazione, installazione, cablaggio e messa in funzione in un solo modello
  • Accuratezza IEC 62053-22 classe 0.5S
  • Facilità di cablaggio grazie alla tecnologia Push-In Plus per i terminali di comunicazione
  • LED automatico e allarme acustico in caso di cablaggio errato
  • LCD bianco, di grandi dimensioni e facile lettura
  • Montaggio su guida DIN
  • Misura bidirezionale della potenza
Caratteristiche ed info per ordinare

Ordering information

Applicable circuits and rated input voltage

Power supply voltage

Dimensions (W×H×D)

Communications

Order code

Single-phase, 2-wire:
100 to 277 VAC
Single-phase, 3-wire:
100 to 240 VAC (L-N) or 200 to 480 VAC (L-L)
Three-phase, 3-wire:
100 to 277 VAC (L-N) or 173 to 480 VAC (L-L)
Three-phase, 4-wire:
100 to 277 VAC (L-N) or 173 to 480 VAC (L-L)

Rated input voltage 85 to 115%

90 × 65 × 90 mm

RS-485, Modbus (RTU) or
CompoWay/F

KM-N2-FLK

Specifications

Ratings

Applicable circuits

Single-phase two-wire, single-phase three-wire, three-phase three-wire, and three-phase four-wire

Maximum number of measured circuits1

Single-phase two-wire: 4 circuits, single-phase three-wire or three-phase three-wire: 2 circuits, three-phase four-wire: 1 circuit

Rated input voltages (power supply voltages)

Single-phase, 2-wire: 100 to 277 VAC
Single-phase, 3-wire: 100 to 240 VAC (L-N) or 200 to 480 VAC (L-L)
Three-phase, 3-wire: 100 to 277 VAC (L-N) or 173 to 480 VAC (L-L)
Three-phase, 4-wire: 100 to 277 VAC (L-N) or 173 to 480 VAC (L-L)

Allowable supply and input voltage range

85% to 115% of rated power supply voltage

Power consumption

7 VA max.

Input current (CT2 primary-side current)2

General-purpose CT: 1 A or 5 A

Rated load: 0.5 VA min.

Rated input frequency

50/60 Hz

Allowable input current

6 A max.

Ambient operating temperature

−25 to 55°C (with no condensation or icing)

Storage temperature

−25 to 85°C (with no condensation or icing)

Ambient and storage humidity

25% to 85%

Operating altitude

2,000 m max.

Installation environment

Overvoltage category II, pollution degree 2, measurement category II

Electromagnetic environment

Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

Compliant standards

EN 61010-2-030, EN 61326-1, and UL 61010-1

Performance

Measurement specifications

Active power

IEC 62053-22 class 0.5S (Accuracy ±0.5% F.S. ±1 digit)3

Reactive power

IEC 62053-23 class 2 (Accuracy ±2% F.S. ±1 digit)1

Sampling cycle

80 ms for 50 Hz and 66.7 ms for 60 Hz

Measured items

Energy consumption (active, regenerative, and reactive), power (active and reactive), current, voltage, power factor, and frequency

Insulation resistance

  • Between all electrical circuits and the case: 20 MΩ min. (at 500 VDC)
  • Between all power supply and voltage inputs and all communications and pulse output terminals:: 20 MΩ max. (at 500 VDC)

Dielectric strength

  • Between all electrical circuits and the case: 2,200 VAC for 1 min
  • Between all voltage and current inputs and all communications and pulse output terminals: 2,200 VAC for 1 min

Vibration resistance

Single amplitude: 0.1 mm, Acceleration: 15 m/s 2 , Frequency: 10 to 150 Hz, 10 sweeps for 8 min each along three axes

Shock resistance

150 m/s 2 , 3 times each in 6 directions (up/down, left/right, forward/backward)

Weight

Approx. 350 g (Power Monitor only)

Degree of protection

IP20

Installation method

DIN Rail mounting

Pulse output

Number of outputs

Number of outputs: 4 (photoMOS relay outputs)
Used for the total power consumption pulse output.

Output capacity

50 mA at 40 VDC
ON residual voltage: 1.5 V max. (for output current of 50 mA)
OFF leakage current: 0.1 mA max.

Output unit

1, 10, 100, 1k, 5k, 10k, 50k, or 100k (wh)
Pulse ON time: 500 ms (Cannot be changed.)

Communications interface

Communications method

RS-485 (2-wire half-duplex with start-stop synchronization)

Communications protocol

Modbus (RTU): Binary. CompoWay/F: ASCII

Baud rate

1.2, 2.4, 4.8, 9.6, 19.2, or 38.4 kbps

Data length

Data length: 7 or 8 bits
Stop bits: 1 or 2 bits
Vertical parity: Even, odd, or none

Maximum transmission distance

1,200 m1

Maximum number of connected Power Monitors

Modbus: 99, CompoWay/F: 31


1. A CT with a different capacity can be specified for each circuit.

2. The KM-series CTs (the KM20-CTF or KM-NCT series) cannot be used. Use general-purpose CTs with a secondary-side output of 1 A or 5 A.

3. The error of the CT or VT is not included.

1. A CT with a different capacity can be specified for each circuit.

2. The KM-series CTs (the KM20-CTF or KM-NCT series) cannot be used. Use general-purpose CTs with a secondary-side output of 1 A or 5 A.

3. The error of the CT or VT is not included.

Avete delle domande?

Siamo a vostra intera disposizione.

Contattateci

Iscrivetevi agli aggiornamenti di prodotti

Newsletter sulle ultime novità e innovazioni in termini di prodotti, soluzioni e servizi direttamente nella vostra casella di posta.

Grazie per la tua iscrizione! Riceverai a breve una E-mail di conferma con un link per attivare il servizio. Questo sistema di iscrizione è stato scelto per ottemperare alla legge sulla privacy e garantisce la riservatezza del tuo indirizzo E-mail.

Purtroppo abbiamo problemi tecnici. Il tuo modulo non è stato ricevuto correttamente. Ci scusiamo per l'inconveniete e ti chiediamo per favore di riprovare più tardi.

Download

Documentazione di prodotto

Scarica le schede tecniche, i manuali e le brochure.

Vai al Download Center

Corsi di formazione

Accedete ai corsi di formazione offerti dai nostri tecnici qualificati. Dal livello principiante ad avanzato.

Visualizzate i corsi di formazione