BU_2SWG

UPS online, di elevata potenza, a montaggio multiplo

Metodo di alimentazione online: alimentazione continua contro le cadute di tensione o le interruzioni di alimentazione istantanee
Pannello operativo a 7 segmenti di facile utilizzo
Ampia varietà di interfacce di comunicazione (USB/RS232C/segnale I/O/ Ethernet. (Deve essere usato con la scheda Ethernet opzionale “SC20G2”)
Morsettiera di ingresso/uscita preinstallata e segnale ON/OFF remoto esterno
Batterie con swapping a caldo

Caratteristiche ed info per ordinare

Ordering information

Main body

Input voltage	Output voltage	Output current/capacity	Order code
220/230/240 VAC	220/230/240 VAC	1,000 VA/700 W	BU1002SWG
220/230/240 VAC	220/230/240 VAC	3,000 VA/2,100 W	BU3002SWG

Related products

Description	Applicable model	Order code
Replacement battery pack	BU1002SWG	BP100XSG
Replacement battery pack	BU3002SWG	BP150XSG
Mounting bracket	BU1002SWG	BUP100SG
Mounting bracket	BU3002SWG	BUP300SG
SNMP/Web card		SC20G2
Contact I/O card		SC08G2

Specifications

		BU1002SWG	BU3002SWG
Method	Operation method	Full-time inverter supply method
Method	Connectable devices	PC, display, and peripherals
Input	Rated input voltage	220/230/240 VAC
	Input voltage range	AC 185±4 to 276±4 V (with 85% or less connection load) AC 210±4 to 276±4 V (with 85% or more connection load)
	Frequency	50/60 Hz ± 4 Hz
	Maximum current	5.8 A	16 A
	Phase	Single-phase, two-wire
	Input plug shape	Schuko CEE 7/7 P	Schuko CEE 7/7 P
	Input protection	Reset-type overcurrent protection device
	Input protection capacity	10 A	20 A
Output	Allowable connection capacity3	1000 VA/700 W	3000 VA/2100 W
	Voltage (effective value)4	220 V mode AC 220 V ± 3% 230 V mode AC 230 V ± 3% 240 V mode AC 240 V ± 3%
	Peak voltage value (In Commercial Power Mode)	220 V mode: AC 310 V ± 6% 230 V mode: AC 324 V ± 6% 240 V mode: AC 338 V ± 6%
	Peak voltage value (In Battery Mode)	220 V mode: AC 310 V+6%/-10% 230 V mode: AC 324 V+6%/-10% 240 V mode: AC 338 V+6%/-12%
	Frequency	50/60 Hz ± 1 Hz
	Phase	Single-phase, two-wire
	Output waveform	Sine wave
	Waveform distortion rate (Rectified load, at rated output)	220V mode: 10% max. 230V mode: 10% max. 240V mode: 12% max.
	Number of output receptacles	IEC60320 C13: 3 pcs. Terminal block: 2 lines	IEC60320 C19: 1 pcs. C13: 5 pcs. Terminal block: 2 lines
	Power failure switching time	Uninterrupted
	Commercial direct shipment (switching time)	4 m sec. max.
	Backup time5	Minimum 5 minutes
Battery	Type	Compact sealed lead battery
	Sealed lead battery life expectancy	4 to 5 years (long operating life) *At ambient temperature of 20°C
	Battery capacity (V/Ah) (x Quantity)	12 VDC/7.2 Ah (× 3)	12 VDC/8 Ah (× 6)
	Charging time	8 hours6
Environment	Operating ambient temperature	0 to 40°C (during operation)/−15 to 50°C (during storage)
Environment	Operating ambient humidity	25 to 85% RH (during use)/10 to 90% RH (during storage)
Dimensions (W x H x D mm)		145 × 395 × 224 (±1) mm7	213 × 537 × 432 (±1) mm8
Weight of unit		Approx. 15.5 kg	Approx. 35 kg
Internal power consumption (max.)		50 W (100 W max.)	55 W (155 W max.)9
Noise regulation (compliance standard)		VCCI Class A
Safety standards / RoHS directive compliance		CE/RoHS compliance
Noise		50 dB max.	55 dB max.
Serial communication (RS-232C) (Interface)		D-Sub 9 pin
Serial communication (USB) (Interface)		B type10
Contact signal (Interface)		D-Sub 9 pin11

Backup time table

BU1002SWG

Connection capacity (W)	20	50	100	200	300	400	500	700	1000	1400
Backup time (Minutes)	180	120	60	35	20	15	10	5	−	−

BU3002SWG

Connection capacity (W)	200	400	600	800	1000	1200	1400	1600	1800	2000	2100
Backup time (Minutes)	92	46	30	20	15	12	10	8	7	5.5	5

Note: These backup times are for reference only. Times may vary according to battery life and external environmental conditions (temperature, etc.).

1. Has to be used with optional Ethernet card “SC20G2”

2. The standard UPS connection signal is NPN. To use a PNP connection, replace with “SC08G” included in the package.

3. Make sure that both the VA value and the W value of the load capacity connected to the UPS are within the range specified here.

4. Check the operation beforehand if the unit is used in any mode other than “220 VAC mode”. In some cases, the maximum voltage of output in Battery Mode may be lower than the maximum voltage in usual operation (commercial power supply).

5. The backup times shown here are for when rated load is connected, at 20°C, and for initial characteristics.

6. When an additional battery unit is connected, the charging time is 24 hours.

7. The height includes the 13 mm height of the rubber feet.

8. The height includes the 56 mm height of the casters.

9. 170 W max when and additional battery unit is connected.

10. USB or RS-232C either is available. (unusable at the same time)

11. The standard UPS connection signal is NPN. To use a PNP connection, replace with “SC08G” included in the package.

1. Has to be used with optional Ethernet card “SC20G2”

2. The standard UPS connection signal is NPN. To use a PNP connection, replace with “SC08G” included in the package.

3. Make sure that both the VA value and the W value of the load capacity connected to the UPS are within the range specified here.

5. The backup times shown here are for when rated load is connected, at 20°C, and for initial characteristics.

6. When an additional battery unit is connected, the charging time is 24 hours.

7. The height includes the 13 mm height of the rubber feet.

8. The height includes the 56 mm height of the casters.

9. 170 W max when and additional battery unit is connected.

10. USB or RS-232C either is available. (unusable at the same time)

11. The standard UPS connection signal is NPN. To use a PNP connection, replace with “SC08G” included in the package.

Come possiamo aiutarti?

Se hai domande o desideri richiedere un preventivo, contattaci o inviaci una richiesta.

+41 (0)41 748 13 13

Richiedi un preventivo

Preventivo per BU_2SWG

Tramite questo modulo può richiedere un'offerta relativa al prodotto prescelto. Completi, per favore, i campi contrassegnati con *. I suoi dati personali verranno trattati secondo le normative vigenti. Le ricordo che il minimo importo fatturabile è di 400 € a cui bisogna aggiungere 25 € di spese amministrative.

Dati personali

Prodotto BU_2SWG

Nome.

Text error notification

Cognome

Text error notification

E-mail

Email error notification

Tel.

Text error notification

Azienda

Text error notification

Nazione

Country error notification

Dettagli del preventivo

Acquisti da Omron o da un distributore/partner?

Select notification error

Titolo/Posizione

Select notification error

Domande o commenti

Text area error notification

Accetto il trattamento dei dati personali secondo la OMRON Privacy Policy

Checkbox error notification

Iscriviti alla newsletter

Checkbox error notification

Grazie per averci richiesto un'offerta. Vi risponderemo non appena possibile.

Purtroppo abbiamo problemi tecnici. Il tuo modulo non è stato ricevuto correttamente. Ci scusiamo per l'inconveniete e ti chiediamo per favore di riprovare più tardi.

Download

Richiedi un preventivo

Software

Power Attendant Lite

L'installazione del software "Power Attendant Lite (PAL)" nel tuo computer o nel tuo sistema consente lo spegnimento automatico dei PC (Windows) mediante la rete. PAL offre maggiori vantaggi rispetto al software SSD (Simple ShutDown).

Scarica Power Attendant Lite

Simple Shutdown Software

Simple Shutdown Software (versione open-source) è in grado di spegnere automaticamente i computer e le unità UPS in caso di problemi di alimentazione, ad esempio quando si verifica l'interruzione dell'erogazione di elettricità. Il software è scaricabile gratuitamente. Utilizzando questo software e il codice sorgente, potrete integrare funzionalità di spegnimento automatico nel vostro sistema Linux o Windows.

Scarica Simple Shutdown Software

PowerAct Pro

Installando “PowerAct Pro Version 5” sul vostro computer o sul vostro sistema, sarete in grado di impostare lo spegnimento automatico dei computer (Windows/Linux/Mac/Unix) tramite la rete. Sono state inoltre aggiunte nuove e utili funzionalità.

Scaricate il software PowerAct Pro .